Why Learning Plumbing Basics is Vital for Bathtub Installation
Why Learning Plumbing Basics is Vital for Bathtub Installation
Blog Article
Here in the next paragraph you can discover additional amazing help and advice all about How to Install a Bathtub Yourself.
Installing a bathtub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a new one is likewise a moderately hard task. If the old tub is easily easily accessible, the project can relocate speedily; if you need to open up a wall to eliminate the old tub and also place the new tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the brand-new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is better to consider using one before you begin. Possibilities are you may require a professional plumber to make tube connections.
This post will assist you mount a brand-new tub in your shower room if you have actually currently acquired a new bathtub as well as don't require to change the setup of your previous water pipes.
Your devices as well as material list ought to consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be rather problematic as a result of the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines are in area in between the tap as well as the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former kind ought to be connected to the tap ends first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Making use of the two wood boards under its feet, place the tub in the called for placement. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the water and also check all joints as well as brand-new pipework for leakages as well as tighten them if required. Load the bathtub and additionally inspect the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling and securing around the bathtub ought to wait up until the bathtub has actually been made use of at the very least once as this will resolve it into its last setting.
Planning for the Installment
To start with, the supporting framework supplied with the bath should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can split relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were brought to that editorial on A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different site. Kindly take the time to promote this blog posting if you enjoyed it. Many thanks for going through it.
Rely on our service. Report this page